Summary: Introduction of K1000 plus e-pipe; accessories of K1000 plus e-pipe kit; the exploded view of K1000 plus e-pipe; How to assembly K1000 plus e-pipe; How to refill e-liquid to sub ohm tank; How to adjust the K1000 plus E-pipe and How to set up K1000 plus 30W e-pipe.
Instruction:
K1000 Plus 30W E-Pipe is 30W full-power output electronic pipe. It can support 0.3-9.9 Ohms atomizers. Ultilizes one battery can't adjust the voltage.
I. Fetures of K1000 Plus 30W E-Pipe:
1.Classical and Modern wooden body and stainless steel button 2. Collocate sub ohm atomizer 0.5ohm atomizer, bigger cloud and better taste 3.LED button: Display the status of product more directly. 4.Long size plastic drip tip: Long size plastic drip tip cooling down cloud temperature more easily, and keep it below 15 degree. 5.Unique bottom design:When not in use, it can stand, no need holder, don't worry about leaking. 6.Built-in battery: Soft package Lithium battery can better combine with the internal chip, more stable 7.USB charge: Mic USB connector, more convenient to charge. No adapter, no charger, only need a USB wire. 8.Energy-saving mode:Energy-saving automatically shut down. System will be in sleep mode if it is not be used or in other operation within 30s. 9. More protection system: Low voltage cut off mode, Short circult protection, Over heat protection, Over time vaping protection, all designed in the chips.

II. Specification of Kamry k1000 plus epipe:
Atomizer coil resistance: 0.5ohm, can match with 0.3ohm Atomizer connector: 510 spring thread Diameter:22mm E-liquid capacity: about 3.0ml Can support wattage: 21-30W (for 0.5ohm) Battery Capacity: built-in Lithium rechargeable battery 1000mAh Output Voltage: 3.3-4.2V Charging time: about 2.5 hours,over charge protection Completely compatible with eGo|510 thread atomizers(0.3Ω-5.0Ω)
III. One K1000 Plus 30W E-Pipe starter kit including:
1 K1000 Plus 30W Pipe MOD (Built-in battery) 1 K1000 Plus Sub-ohm tank clearomizer 2 K1000 Plus Sub-ohm coil heads 1 K1000 Anti-heating drip tip(7.2cm) 1 USB charging cable 1 20ml E-liquid
III. How to use K1000 Plus e-pipe:

A. how to use K1000 Plus Pipe MOD:
a. Power on/off: click the power button 5 times to turn on the K1000 Plus e-Pipe and 5 times again to turn off the K1000 Plus e-Pipe.

b. Vaping: Long press the power button to take a puff.

c. Functions of Micro USB Port--Charging:
The battery power indicator on the screen of K1000 Plus e-pipe will keep flashing when the remaining power of the Li-battery is less than 10%. built in lithium battery, usable charging: can be charged through USB port at the bottom of e-pipe MOD, it will take 2-3 hours to charge the battery with 1A wall adaptor.

B. how to use K1000 plus Sub-Ohm Tank:
a. How to assembly/change the K1000 Plus tank coil head:
Step 1: screw the Tank Body off the Bottom Base.
Step2: Screw the old coil head out from the bottom base (if necessary).
Step3: Screw the new coil head into the Bottom Base again.
* Tips: A loose coil head can cause leaking.

b. How to fill e-liquid to K1000 Plus Tank:
Step 1: Unscrew the Bottom Airflow Adjustable Base from the Tank Body.
Step 2: Fill E-liquid through the slot, and pay attention not to drip it into the central airflow tube.
Step3: Screw the Bottom Airflow Adustable Base into the Tank Boday again.
Then let it stand for several minutes to get the organic cotton completely saturated.

C. How to adjust the K1000 Plus tank airflow
Rotate the Bottom Adjustable Airflow Ring to control air input.The airflow system on the K1000 plus tank system has 2 intake holes, which provides plenty of air to the coils. The airflow system is easy to change and slides smoothly into place. However when fully open, which is what we prefer, the airflow makes a lot of noise and whistles quite a bit.

|