The iStick Pico, just like its name, is preferable, innovative, compact and outstanding (PICO). With a compact size, you can hold it in the palm, much more convenient for usage and portability. Powered by single interchangeable 18650 cell, the iStick Pico also provides you with 75W maximum output and switchable VW/Bypass/TC-Ni/TC-Ti/TCR modes.
Thread type: 510 thread, completely compatible with eGo|510 thread atomizers.
Battery type: removable interchangeable single 18650 battery(continuous discharge current should be above 25A)
Output mode: VW/Bypass/TC(Ni,Ti,SS,TCR-M1,M2,M3) mode
Output wattage: 1-75W
Resistance range: 0.05-1.5ohm (TC modes), 0.1-5.0ohm (VW/Bypass mode)
Temperature range: 100－315℃/200－600℉ (TC modes)
1.Tiny and Cute Appearance: With a compact size, you can hold the kit in the palm, much more convenient for usage and portability.
2.TC-SS and TCR Modes Available: Despite the compact size, the iStick Pico allows an intelligent but yet satisfying draw with 75W maximum output and switchable VW/Bypass/TC(Ni,Ti,SS,TCR) modes
3.Removeable Interchangeable Single 18650 Battery: Users can carry spare cells when on the go and change the cell easily by removing the battery cap only.
4.510 Spring Connector:Completely compatible with eGo|510 thread atomizers; It also retains stainless steel spring loaded 510 connector for strong wear resistance and high adaptability.
5.Micro USB Port Charging: The 18650 battery can be charged in the iStick Pico through the side USB port via 1A wall adapter or computer or charged with an external battery charger. The recommended way is to charge the cell externally as it will take less time to give the cell a full charge.
6.Unique Bottom Design: The ventilation holes at the bottom are for better heat dissipation and the adjustment buttons are located at the bottom as well.
How to Use
Power on/off: Screw off the battery cap, put one high-rate 18650 interchangeable battery (positive side down and negative side up) into iStick Pico 75W Box MOD and finally screw on the battery cap. iStick Pico 75W Box MOD can be prowered on/off by pressing the fire button 5 times.
1. Please make sure you are using a high-rate 18650 battery wholse continuous discharge current should be above 25A.
2. Please be careful not to use battery with torn casing as it is a safety hazard.
3. Before using, please set the wattage within a proper range that the atomizer you installed can work with.
Vaping: Long press the fire button to take a puff.
Stealth on/off: Press the fire button and down button simultaneously when iStick Pico 75W Box MOD is powered on to swith between Stealth On and Stealth off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button one time to see current setting.
Adjustment buttons lock/unlock: Keep pressing up button and down button simultaneously for
two seconds when iStick Pico 75W Box MOD is powered on, then the up and down buttons will be locked and the screen will display "Lock". In the same way, the up and down buttons can be unlocked and the screen will display " Unlock". Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan.
Swith display mode: Keep pressing up button and down button simultaneously for two seconds when iStick Pico 75W Box MOD is powered off, the screen display will rotate 180 degress. You can view the screen from two different angles through this operation.
Swith vaping modes: When iStick Pico 75W Box MOD is powered on, press the fire button 3 times in quick succession, iStick Pico 75W Box MOD will display current caping mode. Press the up or down button to switch among VW, Bypass, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes and then press the fire buton one time or stay in the interface for about 10 seconds to confirm the vaping mode you choose.
1). In VW mode:
When set in VW mode, iStick Pico 75W Box MOD can support a coil whose resistance is within the range of 0.1ohms to 3.5ohms.
Adjust wattage: In this mode, the output wattage can be adjusted from 1W to 75W by pressing up button or down button, up button to increase and down button to decrease. Long press up button or down button cn rapidly increase or decrease the wattage level.
2). In Bypass mode:
When set in Bypass mode, the devide can support a coil whose resistance is within the range of 0.1Ohm-3.5Ohm. Direct output voltage system is applied in this mode. The higher the battery level, the higher the output voltage.
3). In TC-Ni/TC-SS/TCR(M1, M2, M3) Mode:
When set in TC-Ni/TC-SS/TCR(M1, M2, M3) Mode, iStick Pico 75W Box MOD can separetely support Nickel 200, Titanium, and Stainless Steel 316 coils. In TCR(Temperature Coefficient of Resistance) mode, iStick Pico 75W Box MOD can support different temperature control coils within different TVR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05 Ohm-1.5 Ohm).
The Setting of TCR Mode (M1, M2, M3): When iStick Pico 75W Box MOD is powered off, keep pressing the fire button and the up button simultaneously, then you will enter into the TCR (M1, M2, M3) set menu:
1. Press the up or down button to choose among M1, M2, and M3 modes;
2. Press the fire button one time to confirm the mode you choose;
3. Press the up or down button to increase or decrease the TCR value according to the material of the coil you use;
4. Keep pressing the fire button or stay the interface for about 10 seconds to confirm your setting.
Follow are different TCR value ranges for different coils for your reference:
Note: 1. The TCR value in the sheet is 10 multiplied of the actual TCR.
2. Our total range of TCR value is 1-1000.
Adjust wattage: In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) mode, the output wattage can be adjusted from 1W to 75W. Press the fire buton 4 times in quick succession to nter the wattage setting menu and press up or down button to increase or decrease the wattage level. Keep pressing up or down button without looseness to rapidly increase or decrease the wattage level.
Adjust temperature: in TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) mode, temperature can be adjusted from 100-315℃/200－600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Keep pressing up button or down button without looseness can rapidly increase or decrease temperature setting.
Shift between ℃ and ℉: If you increase the temperatureto 315℃, and conture to press the up button, the temperature reading will automatically change to the lowest Fahrenheit (200℉). Equally, if he emperature is set at the lowest Fahrenheit (200℉) and you continue to press the down button, the temperature reading will automatically change to the highest Celsius (315℃).
Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) mode,when they device is powered on, keep pressing the fire button and up button simultaneously for two seconds to lock or unlock atomizer "base resistance". The lock sign will appear when resistance is locked and "Ω" symbol will come back when unlocked.
1. Please lock the resistance when the coil is at room temperature so that iStick Pico 75W Box MOD can display the correct "base resistance".
2. In resistance lock mode, when you remove the coil and then put it back,iStick Pico 75W Box MOD can maintain the same "bse resistance" althrough the coil resistance many increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display "New coil up same down" as the coil resistance may increase within certain range. If it is the same coil, press the down button and if it is a new coil, press the up button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance.
3. When using a common coil or a coil whose resistance is above 1.5 Ohm in C-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) mode by mistake, iStick Pico 75W Box MOD will automatically switch back to VW mode.
Functions of Micro USB Port
The battery power indicator on the screen of Istick Pico 75W will keep flashing when the remaining power of the 18650 battery is less than 10%.
The 18650 battery can be charged in the Istick Pico through USB port via 1A wall adapter or a computer or charged with an external battery charger. If the 18650 battery is charged in the iStick Pio, the battery indictor on the screen will keep flashing during charging and the screen will go out when full charged.
It is recommened to charge the 18650 battery with an external battery charger as it will take less time to give it a full charge.
The firmware can be upgraded by connecting iStick Pico 75W Box MOD with a computer through the USB port via a micro USB cable.
Atomizer Protection: Each time when vaping time exceeds 10 seconds, the output shuts off automatically with "Over 10s" display on the secreen.
Atomizer Low Alert: when the resistance of coil is lower than 0.1 Ohm in VW/Bypass mode or lower than 0.05 Ohm in TC modes, the screen will display " Atomizer Low".
Atomizer Short-circuit & No Atomizer Protection: When atomizer short-circuit occurs, the screen will display " Atomizer Short". The screen will display "No Atomizer" when there is no atomizer connected.
Low-voltage Protection: When the voltage of the battery is below 3.1V, the screen will first display " battery low" and then "Lock", charge the battery to unlock iStick Pico 75W Box MOD.
Temperature Protetion: In TC modes, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". You can coninue to use iStick Pico 75W Box MOD normally.
Temperature Alert: If the temperature of device is over alert temperature, the output will shut off automatically and the screen will display "Device too Hot". You can continue to vape after it cools down.
Weak Battery Alert: In all vaping modes, when the divice is working with an atomizer and the voltage of the cell drops below 2.9V, the screen will display "Weak Battery". Meanwhile, the output power will be reduced accordingly.
1. Only have your iStick Pico repaired by manufacture. Do not attempt to repair the unit by yourself as damage or presonal injury may occur.
2. Do not leave the iStick Pico in high temperatures or damp conditions, otherwise it ma be damaged. Yhe appropriate operation temperature is within 0℃ to 45℃ while charging and -10℃ to 60℃ while using.
3. Please keep out o reach of children.
4. This deviceis not recommended for use by young people or non-smokers.